Fliegl 3-Achs Tieflader

No. 69151

3-Axle Low-Loader Trailer with Articulation
Chassis
- Welded steel construction
- Swivel bogie with heavy-duty ball-type swivel ring
- Foldable rear support
- 2 wheel chocks with holders
- Aluminum side impact protection
- Rear mud flaps across the entire width
- Half-shell fenders on 1st axle with anti-spray flaps; anti-spray flaps behind 2nd and 3rd axles
- 1 spare tire holder for 1 electric bike, with wheel mounting kit
- 1 plastic toolbox, with insert shelf, W=620/H=360/D=440 mm
- Extendable extensions to 3,000 mm (not on rear bevel)
- Storage compartment for wooden planks in the center of the cargo area
- 70 mm wooden planks for extension to 3,000 mm
Lashing eyes on low-loader
- 1 pair of lashing cutouts recessed into the front longitudinal beam at the bend, 10 tons each
- 4 pairs of lashing holes in the outer frame, each rated at 5 tons (for tension straps)
- 7 pairs of lashing studs recessed into the top and sides of the outer frame, each rated at 10 tons
- 1 x at the front on the cradle
- 6 x in the low bed
- 5 pairs of stanchion pockets recessed into the outer frame
- 2 pairs of additional folding lashing eyes, each rated for 10 tons: 1 x on the front frame (protruding) and 1 x recessed in the floor behind the last axle
Towing equipment for trailer turntable
- Towing fork with certified 40 mm towing eye
Axles + Suspension
- SAF drum brake axles
- “Laser-measured axles/chassis” to reduce tire wear and fuel consumption
- Air suspension with lift & lower valve
Wheels and tires
- 235/75 R 17.5”
- Twin-arranged steel rims, factory silver
Brake System
- 2-line air brake system
- Spring-loaded parking brake
- Vehicle stability control system
- Axle load detection via EBS CAN bus signal, for display in the cab; truck must be pre-equipped accordingly; no truck installation (no calibrated scale)
- 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit,
- 24-volt EBS, electronic braking system with EBS connector at the front, with connecting cable
- Caution: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS!
- "TPMS" Tire Pressure Monitoring System according to ECE R 141, display in the towing vehicle via EBS, without truck installation (the truck must be equipped for this),
Electrical
- 24 volts, multi-chamber lights, yellow LED side lighting (with 12/24V voltage converter)
- 2 white front position lights
- 2 white/red rear lane-keeping lights
- 2 x 7-pin reverse-polarity-protected connectors at the front, with connecting cable,
- 1 LED rotating beacon with mount, activated via parking lights (removable light)
- 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm
Floor
- Front ramp with steel/checker plate covering
- Storage compartment recessed into the ramp leading to the front ramp
followed by a 70 mm softwood floor, with steel/checker plate covering in the wheel well area
- Rear ramp with 70 mm softwood floor
- Low-loader deck including rear ramp: 6,500 mm
Access ramps
- Steel ramps: 2,800 mm long, 750 mm wide, laterally adjustable
- Additional ramp lock, foldable at the bottom (to prevent the ramps from sliding sideways; not compatible with the hydraulic side ramp adjustment), covered with wood
- Hydraulically operated via the tractor’s PTO with throttle; control on the left side at the rear
- Hydraulic connection with SVK connector, 10/3 mm, including connecting hose
Country of Approval / Plates
- Type approval according to EC 2007/46 + approval in the Austrian database
- Prepared for two-line license plate holder
- Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear
- Warning sign according to ECE 70
Paint finish
- Frame hot-dip galvanized incl. passivation
- Drawbar galvanized or black, at the manufacturer’s discretion
- Access ramps hot-dip galvanized

Notable equipment:
- Air suspension


When operated with a 24V tractor, ABS and a voltage converter for lights are required

Weights and dimensions:
Gross weight (permitted/technical): 24,000 / 30,000 kg
Payload (permitted/technical): approx. 17,400 / 23,400 kg
Aggregate load (permitted/technical): 24,000 / 30,000 kg
Empty weight (base version): approx. 6,600 kg +/- manufacturing tolerance
Loading dimensions: 11,500 x 2,550 mm
Overall length: approx. 10,900 mm
Overall width (max.): 2,550 mm
Length of offset section: approx. 2,180 mm
Length of low-loader platform
incl. rear bevel approx.: 6,500 mm
Length of rear bevel approx.: 950 mm
Frame width approx.: 2,520 mm
Loading height when loaded in low bed approx.: 860 mm
Hitch height approx.: 900 mm
Drawbar length approx.: 1,900 mm

The sales team at Schwarzmayr would be happy to show you the equipment/machine and asks that you schedule an appointment to view it at our facility.
We are also available on Saturdays until 12:00 PM!

We would also be happy to send you a quote via email.
We look forward to your visit or inquiry.